基于并行多通道卷积长短时记忆网络的轴承寿命预测方法

在预测轴承剩余使用寿命时，数据间的时序特性是一个可以利用的重要隐藏信息。为了更好地提取具有时序信息的特征用于预测，提出了一种基于并行多通道卷积长短时记忆网络（PMCCNN-LSTM）的剩余使用寿命预测模型。该模型主要由两部分组成：前端为并行多通道卷积网络（PMCCNN），提取信号特征，挖掘数据的时序特性，并采用逐层训练和微调的方式提升参数的收敛性；后端为长短时记忆（LSTM）网络，基于特征进行剩余使用寿命预测，并采用加权平均的方法对预测结果进行平滑处理。在一个轴承加速寿命实验的公开数据集上使用留一法验证了该模型的准确性，实验结果表明：所提模型的平均误差与最大误差分别比传统的卷积神经网络（CNN）低23.38%和15.84%，比传统的LSTM低24.14%和19.01%，比卷积长短时记忆网络（CNN-LSTM）低30.32%和23.09%。     

红外菲涅尔透镜的注射超声辅助成型优化

为了提升聚合物红外菲涅尔透镜的光学性能,以其表面微沟槽的成型质量为目标,提出了一种高效的注射超声辅助成型方法,并对工艺参数进行了综合质量优化。首先分析了超声振动对聚合物的加热和加压效应,设计了一套一模两腔的对比试验模具;接着以红外菲涅尔透镜的调制传递函数MTF和齿形平均高度h为优化质量目标,设计了四步骤的多目标优化流程,通过试验设计、基于BP神经网络的质量目标与注射工艺参数关系建模、基于NSGA-Ⅱ的多目标优化和试验验证进行工艺参数的综合优化。实验结果表明:该多目标优化流程具有很高的精度,MTF和h的平均预测误差MPE分别为4.16%和3.32%;注射超声辅助成型的菲涅尔透镜微沟槽具有更高的复制质量,其齿沟槽平均高度h增加了15.6%,且h值的波动量随着h值的增大而增大,MTF值受齿高h均匀性的影响大于齿高h对其的影响。     

Highly efficient chemical mechanical polishing method for SiC substrates using enhanced slurry containing bubbles of ozone gas

In this study, a highly efficient method for chemical mechanical polishing (CMP) of silicon carbide (SiC) substrates using enhanced slurry was proposed and developed. The enhanced slurry contains bubbles of ozone gas generated by ozone gas generator in pure water mixed with a conventional commercially available slurry. Therefore, the enhanced slurry has an oxidizing effect on the Si-face of SiC substrates. To confirm the effectiveness of bubbles enclosing ozone gas, both nano-indentation test and X-ray photoelectron spectroscopy (XPS) analysis were conducted. As a result, the hardness decrease of the Si-face of the SiC substrate was confirmed through the nano-indentation test, and the generation of reaction products was confirmed on Si-face of SiC substrate in the XPS analysis. According to a series of experimental results of our proposed highly efficient CMP method for SiC substrates, the removal rate can be increased when the enhanced slurry was applied, comparing with that for the not only conventional commercially available slurry but also commercially available dedicated slurry.     

Evaluation of the electrical integrity of E-textiles subjected to environmental conditions

E-textiles contain electrically conductive elements and electronic devices that are integrated in textile substrate. Wearable e-textiles are expected to perform like textiles in terms of breathability, conformability, and comfort despite the presence of the electrically conductive elements and electronics. E-textiles are also expected to provide reliable data and signal processing like electronic devices while they are subjected to normal wear and tear under different environmental conditions. The goal of this research was to investigate the electrical integrity of e-textiles while they are subjected to environmental conditions. Different woven samples of electronic-improved outer tactical vest with two narrow conductive traces woven in the warp direction were subjected to range of temperatures and humidity, including extreme conditions. The effects of formation parameters (e-yarn type, number of e-yarns/trace, and weldability), temperature, and humidity on the integrity of the e-textiles were studied. It was found that resistance of networks was affected by changes in air temperature and humidity and the quality of the weld had the greatest impact on electrical integrity of the conductive network. This impact was pronounced in more extreme environmental conditions, which revealed that there was a strong interaction between the weldability, temperature, and humidity.     

Selection of risk response actions with consideration of secondary risks

Secondary risk in project risk management refers to the risk that arises as a direct result of implementing a risk response action (RRA). It is important for project managers (PMs) to consider the effects caused by the secondary risks in the process of RRA selection. The purpose of this paper is to propose an optimization method to address the problem of selecting risk response actions (RRAs) with consideration of secondary risk which is seldom considered in the existing studies. The optimization model aims to minimize the total risk costs with time constraint being placed on the project makespan. By solving the model, an optimal set of RRAs along with the earliest start time for each activity can both be obtained. The results show that secondary risk plays an important role in the process of RRA selection. Project managers should allocate more budget for responding the project risk when the secondary risk is considered, and consider all factors relating to both time and cost so as to select appropriate RRAs to mitigate primary risk and secondary risk.     

臭氧氧化-循环喷淋法处理钨钼选矿废水

采用臭氧氧化-循环喷淋法去除钨钼选矿废水中COD,研究了pH值、臭氧流量、循环频率对COD去除效果的影响。结果表明: 废水COD去除率随pH值、臭氧流量、循环频率增大而增加,在pH值为10、臭氧流量3.0 L/min、循环频率4.0次/min条件下,氧化120 min后废水COD含量由131 mg/L降至11.5 mg/L,COD去除率达91.2%,满足《污水综合排放标准》(GB 8978-1996)一级标准。与O₂、NaClO处理废水COD的对比试验结果表明,循环喷淋法结合O₃表现出较好的COD去除效果。     

Associations between Oil Yield and Profile of Fatty Acids,Sterols, Squalene,Carotenoids, and Tocopherols in Seed Oil of Selected Japanese Quince Genotypes during Fruit Development

Tocopherols, phytosterols, carotenoids, and squalene are present in mature seeds of Japanese quince. Yet, little is known about the relationship between these compounds and oil yield during fruit and seed development. The profile change of lipophilic compounds during fruit and seed development in Japanese quince cultivars “Darius,” “Rondo,” and “Rasa” is investigated. It is shown here that during fruit and seed development, there is a significant reduction, three‐ to over tenfold, in the concentration of minor bioactive compounds in seed oil. It is recorded that delay between synthesis of tocopherols and oil in Japanese quince seeds during the fruit development results in a logarithmic relationship between the oil content and tocopherols concentration in the seed oil (R² = 0.980). Similar trends are observed between oil yield and phytosterols, and carotenoids (R² = 0.927 and R² = 0.959, respectively). The profile of fatty acids during the development of the seeds significantly is changed. The reduction of linoleic, palmitic, and gondoic acids levels and increment of oleic acid is noted. The oil content, profile of fatty acids, and concentration of bioactive compounds in all three genotypes of Japanese quince do not change significantly statistically during the last month of fruit development. Practical Applications: Some fruits are harvested at different degrees of maturity mainly due to a logistic issue and uneven ripening of fruits, which affects the chemical composition of whole fruit including seeds. Therefore, it would be good to know how the chemical composition is changing in plant material during development especially in the last month before harvest. Production of Japanese quince continues to rise year to year and with it the volume of generated by‐products such as seeds. This study demonstrates how it changes the oil content, profile of fatty acid, and concentration of tocopherols, squalene, phytosterols, and carotenoids in the seeds and seed oil of three Japanese quince cultivars “Rondo,” “Darius,” and “Rasa” during plant development. The provided information can be very useful for the manufactories oriented on the processing of by‐products, mainly seeds, generated by other branches of industry, for instance, fruit‐processing.     

纳米Co/rGO磁性复合吸附材料的制备及对Cu2+的吸附性能

以改进Hummer法制备的薄片状氧化石墨烯(GO)为载体和模板负载钴离子，然后采用原位还原法制得纳米金属Co/石墨烯磁性复合吸附材料(Co/rGO)，并将其应用于对Cu2+的吸附和脱除，以期为高效可复用的铜离子脱除剂的合成与应用提供指导。实验结果证实，Co/rGO复合材料具有超顺磁性，能够很方便的使用磁铁进行分离并在无磁场情况下振荡分散。Co/rGO复合材料对Cu2+具有稳定的吸附/脱附性能，实验条件下对Cu2+的最大吸附容量达到117.5 mg/g且5 min内实现吸附平衡，远优于其原料GO的60 min吸附容量27.6 mg/g。本工作系统考察了NaOH加入量、络合剂种类、溶剂种类等关键因素对Co粒子在rGO载体上形貌和分布特性的影响，比较了不同合成条件下的复合材料对Cu2+吸附效果的影响，并对优选条件下制备的Co/rGO复合材料进行了FT-IR, XRD, SEM表征。研究结果表明，纳米Co/rGO磁性材料对Cu2+的吸附过程更符合Freundlich模型，属于多层吸附。室温下吸附焓ΔH=17.81 kJ/mol，吸附反应平衡常数Kθ=3.65。当初始Cu2+浓度为39.22 mg/L时，对Cu2+的吸附率为93.47%，五次吸附/脱附循环后吸附容量仍保持在初始值的94%，每次吸附后溶液中残余Cu2+浓度均满足钴电解液对杂质铜离子的浓度去除要求(5 mg/L)或GB 8978-1996污水综合排放标准3级(2 mg/L)，有望在相关领域发挥作用。